DMO pegs no longer available - alternative?
Close
    
    
Page 1 of 2 12 LastLast
Results 1 to 10 of 19
Like Tree32Likes

Thread: DMO pegs no longer available - alternative?

  1. #1
    Senior Member Sthrnromr's Avatar
    Join Date
    Oct 2018
    Location
    Rural, South Carolina
    Posts
    670

    DMO pegs no longer available - alternative?

    I emailed DMO and Bill told me he stopped making the TW200 foot pegs. So my question is, what are y’all using for larger foot pegs that bolt right up?




    Sent from my iPhone using Tapatalk
    Offroad:
    TW200 - The Goat
    KTM 300 - Orange Dragon
    ATVs

    Onroad:
    Triumphs

    Way too many past bikes and builds to list. I won't bore you. Questions? Just ask.
    =)

  2. #2
    Senior Member PlacerLode's Avatar
    Join Date
    Apr 2012
    Location
    Out West
    Posts
    3,058
    best bet is to replace the OEM TW peg brackets with ProCycle brackets that accept WR and YZ pegs so you can use factory Yamaha steel, stainless steel, Titanium and aftermarket pegs like Raptor Ti, PivotPegz and countless others

    And theres always the low cost cast China pegs that fit OEM TW brackets
    Trail Woman and Sthrnromr like this.
    "It's Like Warm Apple Pie"

    Hidden Content

  3. #3
    Senior Member Trail Woman's Avatar
    Join Date
    Jun 2015
    Location
    Nova Scotia
    Posts
    1,406
    I used these steel pegs...

    https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

    I had to grind off a few corners to allow them to fold but otherwise perfect fit. Awesome.

    Oh yeah and one spring hole was drilled on the wrong side and being such thick steel I opted to bend the spring shorter which worked fine.
    Last edited by Trail Woman; 11-15-2018 at 05:07 AM.

  4. Remove Advertisements
    TW200Forum.com
    Advertisements
     

  5. #4
    Member SwampFox's Avatar
    Join Date
    Dec 2014
    Location
    Summer Grove, LA USA
    Posts
    77
    Quote Originally Posted by PlacerLode View Post
    ...And theres always the low cost cast China pegs that fit OEM TW brackets
    I ordered a set of these ±$16 pegs offa FleaBay. Although this set may not be representative of the whole, the pegs sloped "down & out" and were disagreeable with my knees & lower legs.
    Sthrnromr likes this.
    Lee
    2001 TW200
    2013 CRF250L
    1982 MB-5
    1998 R1100GS/CSM Sidecar
    2012 Zuma 50F + 2006 Burgman 650/Texas Ranger Sidecar <<Mrs. SwampFox's Scooters

  6. #5
    Senior Member Sthrnromr's Avatar
    Join Date
    Oct 2018
    Location
    Rural, South Carolina
    Posts
    670
    Thanks for all the feedback. I’ve had past questionable experiences with China made pegs on eBay so I may steer clear of those for now, but at least good to know they can be an option.

    That being said, does anyone have any experience and opinion on these pegs from IMS?

    http://www.imsproducts.com/Products/...cfm?IDSet=2244

    Also, any differences or opinions on the IMS vs the ProCycle ones here? Besides price of course?

    https://procycle.us/bikepages/tw200.html#wide-pegs

    Thanks again everyone.


    Sent from my iPhone using Tapatalk
    Offroad:
    TW200 - The Goat
    KTM 300 - Orange Dragon
    ATVs

    Onroad:
    Triumphs

    Way too many past bikes and builds to list. I won't bore you. Questions? Just ask.
    =)

  7. #6
    Senior Member Lyterx's Avatar
    Join Date
    Jun 2014
    Location
    Etters, Pa
    Posts
    474
    Quote Originally Posted by Sthrnromr View Post
    I emailed DMO and Bill told me he stopped making the TW200 foot pegs. So my question is, what are y’all using for larger foot pegs that bolt right up?




    Sent from my iPhone using Tapatalk
    I think they will make them if you order enough sets. I would order a set or buy a set if they were available.
    1991 TW200

  8. #7
    Senior Member PlacerLode's Avatar
    Join Date
    Apr 2012
    Location
    Out West
    Posts
    3,058
    Quote Originally Posted by Lyterx View Post
    I think they will make them if you order enough sets. I would order a set or buy a set if they were available.
    Last time I spoke with Bill back in 2016 and bought what he said was the last batch of TW pegs he wanted to be done with TW pegs as he had too many whiners where with all his other pegs he had no problems ever. I think the stagger / offset on the TW pegs befuddled a few people. DMO pegs for the BW200 are also fit for the TW

    I like those IMS pegs they have always made good products
    Sthrnromr and joeband like this.
    "It's Like Warm Apple Pie"

    Hidden Content

  9. #8
    Senior Member stagewex's Avatar
    Join Date
    Jun 2016
    Location
    New Rochelle, New York
    Posts
    1,775
    I have IMS shifters on 3 of my bikes (including the TW) and they are very well built. Don't know anything about their footpegs.

    Swapping-out the stock footpegs was the very first thing I did after I bought my TW. Couldn't show it to anyone until I did.
    I went for the ASM-Wide Pegs from ProCycle. Spendy but actually built better than the entire bike. No adustments, drilling holes, filing burrs, etc.
    Perfect fitment:


    IMG_4953.JPG

    I'm not kidding about the build quality. Look at it compared to the stock Yamaha footage no matter what size it is:
    IMG_4952.JPG


    With an IMS Extended Shifter. I'm size 11.5-12.00 shoe/bootsize.
    IMG_4955.JPG
    Last edited by stagewex; 11-15-2018 at 04:47 PM.
    Sthrnromr, Lyterx and jbfla like this.
    2008 Vespa 150"S" (Elec & Kick Start)
    2007 Ural Patrol (2WD, Elec & Kick Start)
    2006 Yamaha TW200 (Elec & Kick Start)
    1995 BMW K75 (Elec Start)
    1991 Honda XR250L (Kick Start Only)
    1986 Yamaha BW200ES (Elec & Kick Start)
    1969 BMW r60/2, US Model (Kick Start Only)

  10. #9
    Senior Member Tiny-Wheel-200's Avatar
    Join Date
    May 2013
    Location
    Wasilla, Alaska
    Posts
    726
    ive ridden with a set of china pegs that were ten dollars for alot of years and they're still intact and serving well. they're good enough for who they're for.

    Sent from my LGL63BL using Tapatalk
    Tweaker, Sthrnromr and Dryden-Tdub like this.

  11. #10
    Senior Member nihil's Avatar
    Join Date
    Jan 2018
    Posts
    313
    I've put about 4k miles on these since spring:
    https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

    Quality is reasonable. Not a "pretty" or trick product, no yummy CNC goodness, but very functional and fit with no modifications.

Page 1 of 2 12 LastLast

Sponosred Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. My new longer pegs
    By rivershot in forum Performance and Customization
    Replies: 3
    Last Post: 02-08-2015, 10:59 AM
  2. DMO Pegs
    By r80rt in forum TW200 Classifieds
    Replies: 10
    Last Post: 10-13-2014, 07:44 PM
  3. Replies: 8
    Last Post: 08-25-2014, 06:30 PM
  4. DMO Specialties 0 off-set pegs
    By troll in forum Performance and Customization
    Replies: 6
    Last Post: 06-21-2014, 11:01 PM

Search tags for this page

asm widepegs
,
dmo foot pegs
,

dmo footpegs tw200

Click on a term to search for related topics.