Did I order the correct part?
Close
    
    
Page 1 of 2 12 LastLast
Results 1 to 10 of 15
Like Tree7Likes

Thread: Did I order the correct part?

  1. #1
    Senior Member Holdnon72's Avatar
    Join Date
    Jan 2014
    Location
    New Jersey
    Posts
    592

    Did I order the correct part?

    I stripped out the carb drain screw on my 2013 Tdub
    Ordered a new one but noticed in the bag their is a steel washer,rubber o-ring and spring along with the drain screw

    Will I need all this when replacing the drain screw?



    Thanks
    2013 TW200 Ims super stock pegs,zeta pro bend xc hand-guards,manrack,zeta muffs,Gerbing ultra light heated gloves

  2. #2
    Senior Member gamorg02's Avatar
    Join Date
    May 2014
    Location
    Central NY
    Posts
    174
    as per ron ayers it looks like it, but its called air screw.

    27 4JP-14104-00-00 AIR SCREW SET

    haven't been in the tw's carbs yet but all other drain screws i've done are sans any spring, that looks more like a pilot screw assembly.

  3. #3
    Senior Member greenbomb's Avatar
    Join Date
    Apr 2014
    Location
    cherokee village Arkansas
    Posts
    229
    Yep AIR Screw

    drain screw 4jp-14323-00-00
    Last edited by greenbomb; 06-29-2014 at 09:50 PM.
    Look at the bottom of this page under SIMILAR THREADS
    Norm in Arkansas
    2006 TW , Kick Starter , Shinko 241 front 4;00/18 ,Vesrah HD clutch springs. Carb jet Kit, Amsoil 10-40 , ALLSBALLS steering head bearings, Jimbo shield. Zeta drop -down bend handguards
    Ricochet skidplate from IMMIX RACING , BIKEMASTER Supersport mirrors XT350 fuel tank , member big foot pegs

    Honda XR 600 , KTM 300 , BMW 1100 gs , 327 Cushman Truckster , KTM 625 SXC . Ural with sidecar

  4. Remove Advertisements
    TW200Forum.com
    Advertisements
     

  5. #4
    Senior Member PlacerLode's Avatar
    Join Date
    Apr 2012
    Location
    Out West
    Posts
    3,056
    Thats the correct part I just had mine out this morning and the spring and o-ring stayed inside the bowl when I removed it. funny they call it an "air screw" but then again I guess it does does let air into the float bowl
    "It's Like Warm Apple Pie"

    Hidden Content

  6. #5
    Senior Member greenbomb's Avatar
    Join Date
    Apr 2014
    Location
    cherokee village Arkansas
    Posts
    229
    Well I guess it would let gas out of the bottom of the float bowl BUT the fuel drain screw is in the side of the float bowel . hope you did not tighten it down too hard . Just might find your bike runs better is you back it out a turn or two

    HOLDNON72 use www.partzilla.com might have to use a year or two earlier but there pretty much the same


    Quote Originally Posted by PlacerLode View Post
    Thats the correct part I just had mine out this morning and the spring and o-ring stayed inside the bowl when I removed it. funny they call it an "air screw" but then again I guess it does does let air into the float bowl
    Last edited by greenbomb; 06-29-2014 at 10:10 PM.
    Look at the bottom of this page under SIMILAR THREADS
    Norm in Arkansas
    2006 TW , Kick Starter , Shinko 241 front 4;00/18 ,Vesrah HD clutch springs. Carb jet Kit, Amsoil 10-40 , ALLSBALLS steering head bearings, Jimbo shield. Zeta drop -down bend handguards
    Ricochet skidplate from IMMIX RACING , BIKEMASTER Supersport mirrors XT350 fuel tank , member big foot pegs

    Honda XR 600 , KTM 300 , BMW 1100 gs , 327 Cushman Truckster , KTM 625 SXC . Ural with sidecar

  7. #6
    Senior Member Holdnon72's Avatar
    Join Date
    Jan 2014
    Location
    New Jersey
    Posts
    592
    This is the one I stripped
    I stripped the head not the internal carb threads
    I was using a Phillips instead of a Jis screwdriver,but now I know and have the Jis screwdriver set.
    Greenbomb why would a drain screw make the bike run differant?
    As far as I know,you just lighly snug the drain screw

    2013 TW200 Ims super stock pegs,zeta pro bend xc hand-guards,manrack,zeta muffs,Gerbing ultra light heated gloves

  8. #7
    Senior Member scotti158's Avatar
    Join Date
    May 2013
    Location
    Groton, NY
    Posts
    2,663
    Quote Originally Posted by greenbomb View Post
    Yep AIR Screw

    drain screw 4jp-14323-00-00
    I agree. Here is a LINK showing the drain screw as 4JP-14323-00-00. No washers or O-rings.
    PlacerLode likes this.
    2013 Yamaha TW200

    1996 Yamaha TW200

    1995 Kawasaki KLR650

    2002 Yamaha RoadStar 1600 with sidecar

  9. #8
    Senior Member Holdnon72's Avatar
    Join Date
    Jan 2014
    Location
    New Jersey
    Posts
    592
    This must be how they are packaging it now.

    Take a look at this page,it states to USE part#4JP-14104-00

    http://www.m-and-d.com/YAM-4JP-14323-00-00.html
    Last edited by Holdnon72; 06-30-2014 at 07:00 PM.
    2013 TW200 Ims super stock pegs,zeta pro bend xc hand-guards,manrack,zeta muffs,Gerbing ultra light heated gloves

  10. #9
    Senior Member Holdnon72's Avatar
    Join Date
    Jan 2014
    Location
    New Jersey
    Posts
    592
    They are certainly the Same screw

    I will make sure to use nothing but my new Jis screwdrivers for now on

    PlacerLode and jb882 like this.
    2013 TW200 Ims super stock pegs,zeta pro bend xc hand-guards,manrack,zeta muffs,Gerbing ultra light heated gloves

  11. #10
    Senior Member greenbomb's Avatar
    Join Date
    Apr 2014
    Location
    cherokee village Arkansas
    Posts
    229
    Greenbomb why would a drain screw make the bike run differant?

    The drain screw would NOT . BUT the AIR screw would as it changes the idle mixture

    And of course I did not get the full jest of Placerlode remarks . My Bad
    Good to be informed thanks for the Pics and such .


    "The only real mistake is the one from which we learn nothing."
    Last edited by greenbomb; 07-04-2014 at 02:21 PM.
    Look at the bottom of this page under SIMILAR THREADS
    Norm in Arkansas
    2006 TW , Kick Starter , Shinko 241 front 4;00/18 ,Vesrah HD clutch springs. Carb jet Kit, Amsoil 10-40 , ALLSBALLS steering head bearings, Jimbo shield. Zeta drop -down bend handguards
    Ricochet skidplate from IMMIX RACING , BIKEMASTER Supersport mirrors XT350 fuel tank , member big foot pegs

    Honda XR 600 , KTM 300 , BMW 1100 gs , 327 Cushman Truckster , KTM 625 SXC . Ural with sidecar

Page 1 of 2 12 LastLast

Sponosred Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Let's go with another T-Dub Club Shirt order!
    By Rohnsman in forum General Discussion
    Replies: 19
    Last Post: 07-16-2018, 08:06 PM
  2. i need to know exactly before i order
    By 1RobAusdemore in forum Technical Help
    Replies: 7
    Last Post: 08-12-2014, 08:59 PM
  3. correct front boot size for 87 tw
    By hertha in forum Technical Help
    Replies: 4
    Last Post: 12-29-2012, 07:26 AM
  4. Best place to order OEM parts
    By nfpgasmask in forum General Discussion
    Replies: 13
    Last Post: 12-14-2012, 10:32 PM
  5. How To Order Parts from Japan
    By sorethumb in forum Performance and Customization
    Replies: 10
    Last Post: 02-17-2011, 02:20 AM